Skip to content

NCEP 85T16 N Channel Mosfet To-220

2 reviews Add a review

Rs130

In stock: 250

Description

NCEP 85T16: If your DC-DC converter, synchronous rectifier, motor controller, or power supply board needs a strong N-channel MOSFET in a TO-220 body, and the old part was rated 85 V and 160 A, this is the part to order. Its on-resistance is under 3.8 milliohms at most, so it wastes very little power as heat even at high current. It does not fit circuits that run above 85 V, above 160 A of steady current, or above 20 V on the gate. Check the checks below before you order, so the voltage, current, and size all match your board.

This is an original, high-quality part.

What NCEP85T16 does

A MOSFET is a switch that a small gate signal turns on and off. When it is on, current flows from drain to source through a very low resistance. On this part that resistance is 3.1 milliohms in the typical case at 10 V on the gate, so a high current can pass with only a small voltage drop. When it is off, it blocks up to 85 V between drain and source. The total gate charge is 105 nC, which keeps switching losses low in fast switching work and in synchronous rectification, where the part switches in step with the circuit instead of a diode doing the job.

 

This part sits in the same N-channel TO-220 family as the 150 V part on the neighbouring page, but the two are not swaps for each other. Their voltage and current limits differ, so order by your own circuit’s numbers, not by family.

Key features

  • N-channel Super Trench power MOSFET in a TO-220-3L body
  • 85 V drain-source voltage limit
  • 160 A steady drain current at 25 °C case temperature, 112 A at 100 °C
  • 480 A pulsed drain current limit
  • Ultra-low on-resistance: 3.1 milliohms typical, 3.8 milliohms at most, at 10 V on the gate
  • 220 W power dissipation limit at 25 °C case temperature
  • Gate drive up to ±20 V
  • Low gate charge: 105 nC in total
  • Fast switching: 30.5 ns turn-on delay, 95 ns turn-off delay in the test circuit
  • Junction temperature up to 175 °C
  • 100% UIS tested, as stated in the datasheet

Checks before you order

  • Voltage: the drain-source voltage on your circuit must stay at or below 85 V. Above that, this part is the wrong pick, even if the current fits.
  • Current and heat: the steady current must stay at or below 160 A at a cool case, and only 112 A when the case runs at 100 °C. Work out the heat from your real current and the on-resistance in the table below, and use a heatsink that keeps the case cool enough. The 220 W limit counts only with the case held at 25 °C.
  • Gate drive: drive the gate with 10 V to get the rated low on-resistance. Never push the gate past ±20 V. The part starts to turn on between 2.5 V and 4.5 V on the gate, but that is only the turn-on point, not the drive level for full current.
  • Package: your board footprint must be TO-220 with three leads. This is a through-hole power part with a metal tab for a heatsink. It is not a surface-mount part.
  • Body marking: the body must show NCEP85T16. If your old part shows a different code, stop and check your board list again.
  • Switching job: if your circuit is a plain on-off switch that rarely changes state, a slower part may do. This part earns its place in fast switching and synchronous rectification work, where its low on-resistance and low gate charge both matter.

Specifications

All figures below are from the manufacturer datasheet for this exact part, at 25 °C unless noted. No figure here was guessed.

Type N-channel Super Trench power MOSFET
Package TO-220-3L, 3 leads
Body marking NCEP85T16
Drain-source voltage 85 V
Gate-source voltage ±20 V
Continuous drain current 160 A at 25 °C case; 112 A at 100 °C case
Pulsed drain current 480 A
Power dissipation 220 W at 25 °C case
On-state resistance 3.1 milliohms typical, 3.8 milliohms at most, at 10 V gate, 80 A
Gate threshold voltage 2.5 V to 4.5 V
Total gate charge 105 nC
Junction and storage temperature −55 °C to +175 °C

Other names for the same part (good to know)

Buyers and repair techs write this same part a few ways. NCEP85T16 is the full part code. 85T16 MOSFET is the short code buyers type when they search. 85V 160A MOSFET is the plain rating buyers search by. N channel MOSFET TO-220 is the plain type-and-size name. Synchronous rectification MOSFET is the job name buyers use, since this part is most often fitted where a fast switch must act in place of a diode. If you see NCEP85T16 on a TO-220 body, and your circuit needs 85 V and 160 A, this page is the right match. Do not judge by the code alone — check the voltage, the current, and the TO-220 size too.

Frequently Asked Questions

What do 85 V and 160 A mean for this part?

85 V is the most the part can block between drain and source when it is off. 160 A is the most steady current it can carry with the case held at 25 °C. At a 100 °C case the steady limit falls to 112 A, so heat control is part of the rating, not an extra.

What is synchronous rectification, in plain words?

In a power converter, a diode normally lets current pass one way and blocks it the other way, but it wastes power as heat. In synchronous rectification, a MOSFET like this one switches on and off in step with the circuit and does the diode’s job with far less loss, because its on-resistance is so low.

What does low on-resistance mean for heat?

When the part is on, it still has a small resistance — 3.1 milliohms in the typical case. Current through that resistance turns into heat. A lower resistance means less heat at the same current, which is why this part suits high-current boards.

What gate voltage does this part need?

Drive the gate with 10 V for the rated low on-resistance. The gate must never go past ±20 V. The part starts to turn on between 2.5 V and 4.5 V, but that turn-on point alone does not give full current — use the full 10 V drive.

Does this part fit a TO-220 footprint?

Yes, if your board has a TO-220 three-lead footprint with room for the heatsink tab. This is a through-hole part, not a surface-mount part, so the leads go through holes in the board.

What is the price of this part?

Check the live price on the product page. The price shown there is the current one.

Use note kept from the old page: this part was listed before for DC/DC converters, synchronous rectifiers, battery-powered equipment, motor controllers, power supplies, and inverters, with high-frequency switching and ultra-low on-resistance, and that use still stands.

You can view and download the datasheet for this part from the Download button on this page.

SKU85T16-FET TAGS160A MOSFET

Reviews

5.0 2 reviews
Aqib Javed

Highly recommended seller and items.

Imran Ali

Excellent experience with this purchase.

Add a review

Your email address will not be published. Required fields are marked *

You may also like

Need Help?
Ask Here