Skip to content

Hall Effect Current Sensor Sinomags STB-20HA-A

Rs1,600

In stock: 15

Description

Hall Effect Current Sensor Sinomags STB-20HA-A is a closed-loop Hall effect current sensor with TMR technology for measuring DC, AC, pulse and irregular-waveform current up to a 20A nominal value. It gives a 4V output at 20A from a ±15V supply, so it fits current sensing and overcurrent protection in solar inverters, UPS systems, variable frequency converters, DC dynamos and switched-mode power supplies. It does not fit jobs that need a 5V Arduino-style sensor module — this is an industrial sensor that needs a dual ±15V supply — and it does not fit a thick busbar, because the primary hole takes one wire up to 1.6mm diameter. This is an original, high-quality part.

What it does

The STB-20HA-A measures the current flowing through a wire passed through its aperture and gives out a voltage that follows that current. At 20A the output is 4V. Because it works on the closed-loop principle with TMR technology, it stays accurate and fast: linearity ±0.5%, accuracy ±0.8% at 25°C, step response 1.5µs and bandwidth 150kHz. It measures DC, AC, pulse and irregular waveform current, in both directions, with a measuring range of ±60A.

Key features

  • Closed-loop TMR technology — fast and accurate current sensing
  • 20A nominal current, ±60A measuring range
  • 4V output at 20A (3.96–4.04V)
  • ±15V ±5% dual supply
  • Linearity ±0.5% of IPN, accuracy ±0.8% at 25°C
  • Step response 1.5µs, bandwidth 150kHz (-3dB)
  • Measures DC, AC, pulse and irregular waveform current
  • Wide working temperature: -40°C to +85°C
  • 6-pin through-hole package, 18.5 × 15.4 × 21mm, 13g
  • UL94V-0 material, RoHS

Checks before you order

  • Supply: Your board must provide a dual ±15V supply (±5%). This sensor does not run on 5V alone.
  • Current rating: This is the 20A part. The same series also has 10A, 15A, 25A, 30A, 50A and 60A parts — order the rating your job needs.
  • Primary wire: Pass one wire up to 1.6mm diameter through the aperture, one turn only.
  • Pinout: 6 pins — 1: -Vcc (-15V), 2: GND (0V), 3: +Vcc (+15V), 4: Vout, 5: Primary input current (+), 6: Primary input current (-). Check the pinout in the datasheet before soldering.
  • Marking: The part is marked “STB-HA/A 20” on its body — that is the same part as STB-20HA-A (series STB-HA/A, 20A variant).
  • Not an ACS712 module: This is an industrial closed-loop sensor, not a 5V Arduino current sensor module. It does not fit Arduino-style 5V boards directly.
  • Not L18P020D15: SunTech also sells the Tamura L18P020D15 (20A, open-loop Hall). Both are 20A sensors with a 4V output, but they are different parts with different pinouts — check which one your board needs before you order.

Specifications

All figures below are for the STB-20HA/A part at +25°C unless noted. No figure here was guessed.

Parameter Value
Type Closed-loop Hall effect current sensor (TMR technology)
Primary nominal current (IPN) 20A rms
Primary current measuring range (IPM) ±60A
Output voltage (Vout) 4V (3.96–4.04V) at 20A
Supply voltage (VC) ±15V ±5%
Current consumption (IC) 18 + IP×NP/NS mA (NS = 1000)
Linearity (εL) ±0.5% of IPN
Electrical offset voltage (VOE) ±40mV max (at 0A)
Accuracy at 25°C (X) ±0.8% of IPN
Thermal drift of offset (TCVOE) ±1% of IPN
Thermal drift of gain (TCVO) ±1.5%
Step response time (tr) 1.5µs
Frequency bandwidth (-3dB) (BW) 150kHz
Primary conductor 1.6mm diameter × 1 turn
Working temperature (TA) -40°C to +85°C
Storage temperature (Tstg) -40°C to +105°C
Absolute maximum supply voltage (Vcc_max) ±18V
ESD rating (HBM) 4kV
Pins 6 (through-hole)
Dimensions 18.5 × 15.4 × 21mm
Mass 13g
Material UL94V-0, RoHS

Other names for the same part (good to know)

  • STB-20HA/A
  • STB-HA/A 20 (body marking)
  • Sinomags STB-20HA-A
  • 20A closed-loop TMR current sensor
  • Sinomags STB-HA/A series 20A sensor

Frequently Asked Questions

What is the STB-20HA-A used for?

Measuring current in solar inverters, UPS systems, variable frequency converters, DC dynamos and switched-mode power supplies — also for overcurrent detection and protection.

What power supply does it need?

A dual ±15V supply (±5%). It does not work on 5V alone. The absolute maximum supply is ±18V.

What output do I get at 20A?

4V (3.96V to 4.04V). The output follows the measured current in both directions, up to a ±60A measuring range.

Is this the same as an ACS712 20A module?

No. The ACS712 is a 5V Arduino-style module. The STB-20HA-A is an industrial closed-loop TMR sensor with a ±15V supply, 4V output, 1.5µs response and 150kHz bandwidth.

What does the marking “STB-HA/A 20” mean?

It is the body marking of this same part: series STB-HA/A, 20A variant. The order code is STB-20HA-A.

What is the difference between STB-20HA-A and L18P020D15?

Both are 20A sensors with a 4V output, but the STB-20HA-A is a closed-loop TMR sensor (1.5µs, 150kHz, ±0.5% linearity) while the L18P020D15 is an open-loop Hall sensor (≤5µs, DC~100kHz, ±1% linearity). They have different pinouts, so check your board before you order.

Download the datasheet: use the Download button on this page for the official Sinomags STB-HA/A series datasheet (Ver 5.3).

SKU: STB-20HA-A-CT

SKUSTB-20HA-A-CT

Reviews

No reviews yet

Be the first to share your experience with this part.

Be the first to review “Hall Effect Current Sensor Sinomags STB-20HA-A”

Your email address will not be published. Required fields are marked *

You may also like

Need Help?
Ask Here