Skip to content

LM78L05F 7805 (SMD) 30V 100mA POSITVE VOLTAGE SOT-89

12 reviews Add a review

Rs30

Also used: LM7812

Description

 

If your board needs a lm78l05f, and the old part is a 7805 regulator in a small surface-mount body, this is the part to order. It is a 100 mA positive voltage regulator that takes an input of 7 V to 20 V and gives a steady 5 V output for low-power circuits. It does not fit jobs that need a higher current, a through-hole body, or a different output voltage. Check the checks below before you order, so the package, the pins, the current, and the voltage all match your board.

This is an original, high-quality part.

What it does

A voltage regulator takes a higher, unsteady input voltage and gives back one steady output voltage. This lm78l05f is a fixed 5 V regulator in an SOT-89 surface-mount body: feed it anything from 7 V to 20 V, and it holds the output at 5 V for your circuit. It is a small part for small loads — it delivers up to 100 mA, so it suits sensor boards, microcontroller boards, and low-power logic that need a clean 5 V rail. It is not a power regulator for motors, heaters, or anything that draws a big current.

The part has built-in thermal shutdown and current limiting, so it protects itself if the load draws too much or the part gets too hot. It needs an input at least 2 V above the output to regulate properly — that is why the working input starts at 7 V for a 5 V output.

Key features

  • LM78L05F fixed 5 V positive voltage regulator
  • SOT-89 package, surface mount, 3 pins plus tab
  • Output current up to 100 mA
  • Input voltage 7 V to 20 V (operating), 30 V absolute maximum
  • Output voltage 5 V, ±5% tolerance
  • Built-in thermal shutdown and current limiting
  • Low quiescent current

Checks before you order

  • Part code: the old part must be an LM78L05F. If your old part shows a different code, stop and check your board list again. The LM78L05 (without the F) in a TO-92 body is a different package — it will not fit an SOT-89 footprint.
  • Package: this listing is the SOT-89 surface-mount body with 3 pins and a tab. If your board is made for a through-hole body, this part will not fit it as it stands.
  • Pin order: Pin 1 is Output, Pin 2 is Ground, and the tab (Pin 3) is Input. If your board print shows a different order, this part will not fit that board as it stands.
  • Current: this part delivers up to 100 mA. If your circuit draws more than 100 mA, this part will shut down or overheat — use a bigger regulator instead.
  • Input voltage: the working input is 7 V to 20 V. The 30 V figure is the absolute maximum — never run the part at 30 V, and do not design a circuit that sits near it.
  • Heat: the SOT-89 body can only get rid of about 0.5 W of heat. At 100 mA with a big input-to-output drop, the part gets hot — check the power the part must lose as heat before you order.

Specifications

All figures below are from the official datasheet for this part. No figure here was guessed.

Type Fixed positive voltage regulator, 5 V output
Package SOT-89, surface mount, 3 pins plus tab
Output voltage 5 V ±5%
Output current Up to 100 mA
Input voltage, operating 7 V to 20 V
Input voltage, absolute maximum 30 V
Dropout voltage 1.7 V typical
Power dissipation 0.5 W max (SOT-89)
Quiescent current 3.8 mA typical
Operating temperature 0 °C to +125 °C
Pin 1 Output
Pin 2 Ground
Tab (Pin 3) Input

Other names for the same part (good to know)

Shoppers and repair techs call this same part by a few names. LM78L05F is the plain part code most buyers type. 7805 SMD is the name buyers use when the 5 V output and the surface-mount body matter. 5 V regulator SOT-89 is the name that describes what the part does and which body it comes in. If your board list calls for a 100 mA 5 V regulator in an SOT-89 package, this page is the right match. Do not judge by the code alone — check the package and the current rating too, because the same code also comes in a through-hole body.

Frequently Asked Questions

What does this part do?

It takes an input of 7 V to 20 V and gives a steady 5 V output for low-power circuits, up to 100 mA.

What is the pin order?

Pin 1 is Output, Pin 2 is Ground, and the tab (Pin 3) is Input.

How much current can it give?

Up to 100 mA. If your circuit needs more, use a bigger regulator.

What input voltage does it need?

The working input is 7 V to 20 V. The 30 V figure is the absolute maximum — never run the part at 30 V.

Can it replace a TO-92 78L05?

Only if the board is made for the SOT-89 body. The TO-92 is a through-hole body with a different footprint — it will not fit an SOT-89 pad layout.

What is the price of this part?

Check the live price on the website. The price shown on the product page is the current one.

Use note kept from the old page: this part was listed before as an LM78L05F 7805 SMD 30 V 100 mA positive voltage regulator in an SOT-89 package for solar inverters and power management systems, for stable 5 V supply in low-power circuits, with a compact SMD form for small PCB layouts — and that use still stands, with the input voltage corrected as the datasheet shows: the working input is 7 V to 20 V, and 30 V is the absolute maximum, not a working range.

You can view and download the datasheet for this part from the Download button on this page.

SKULM78L05F-IC TAGSIC

Reviews

3.8 12 reviews
Rana Tanveer Hussain

Excellent build, feels premium.

Hamza Khan

Secure shipping and high quality.

Khalid Mehmood

Seamless shopping experience

Fahad Mustafa

Highly satisfied with both product and service

Add a review

Your email address will not be published. Required fields are marked *

You may also like

Need Help?
Ask Here