Skip to content

LM7812 Positive Voltage Regulator To-220

12 reviews Add a review

Rs50

Also used: LM7812 L7806V 78M05 L7805

Description

 

If your board needs a voltage regulator to-220, and the old part is a 12v 1a voltage regulator in a TO-220 package, this is the part to order. It gives a fixed 12V rail with a heatsink tab for power supplies and inverter boards. It does not fit boards that need a different voltage, a higher current, or a surface-mount part. Check the checks below before you order, so the voltage, the current, the pins, and the heat plan all match your board.

This is an original, high-quality part.

What it does

A linear regulator takes a higher, unsteady DC voltage and holds its output at one fixed voltage. This lm7812 part holds its output at 12V while the input and the load shift a little. It is a three-terminal part: Input, Ground, Output. With a heatsink it can deliver over 1A, and the sheet lists its output current up to 1.5A. It has built-in thermal overload protection, short-circuit protection and safe-area protection, so a fault shuts it down instead of burning the board.

The input must stay above the output by at least the dropout voltage, which is 2V at 1A. That means the input needs to be about 14V or more for a steady 12V output. The sheet tests the output over a 14.5V to 27V input range. The extra volts turn into heat, so work out your heat before you order: at 19V in and 1A out, the part must shed about 7W, and that needs a proper heatsink on the metal tab.

Key features

  • LM7812 12V positive voltage regulator, three-terminal
  • TO-220 package, through hole, with a metal tab for a heatsink
  • Fixed 12V output, 11.5V to 12.5V at 25 °C
  • Output current 1A typical, up to 1.5A
  • Dropout voltage 2V at 1A
  • Thermal overload protection, short-circuit protection, safe-area protection
  • Input bypass capacitor 0.33 µF, output capacitor 0.1 µF
  • Operating junction temperature 0 °C to 125 °C

Checks before you order

  • Part code: the old part must be a LM7812 in a TO-220 package. If your old part shows a different code, stop and check your board list again.
  • Voltage: the input must stay inside the tested 14.5V to 27V range for steady work, and never above the 35V absolute maximum. The output is a fixed 12V — it cannot be set to another voltage.
  • Current and heat: the load must stay at or below 1A in normal use. Heat in watts is roughly (input volts minus 12V) times load amps. At 19V in and 1A out that is about 7W, so the part needs a proper heatsink on its tab. A bare part with no heatsink will overheat and shut down.
  • lm7812 pinout: Pin 1 Input, Pin 2 Ground (joined to the metal tab), Pin 3 Output. This is the positive-regulator order. Never copy a 79xx negative-regulator layout for this part — the 79xx pins are the mirror of this order.
  • Capacitors: fit a 0.33 µF capacitor on the input and a 0.1 µF capacitor on the output, close to the part.
  • Minimum load: the regulator needs at least a 5 mA load to hold its output steady.

Specifications

All figures below are from the official datasheet for this part. No figure here was guessed.

Type Three-terminal positive voltage regulator, fixed output
Package TO-220, through hole, metal tab for heatsink
Output voltage, fixed 12 V
Output voltage at 25 °C 11.5 V to 12.5 V
Output voltage, IO 5 mA to 1 A, VI 14.5 V to 25 V 11.4 V to 12.6 V
Output current 1 A typical, up to 1.5 A
DC input voltage, absolute maximum 35 V
Line regulation, VI 14.5 V to 30 V, IO 500 mA 240 mV max
Load regulation, IO 5 mA to 1.5 A 240 mV max
Quiescent current 8 mA max
Dropout voltage 2 V (IO = 1 A, 25 °C)
Short-circuit peak current 2.2 A
Operating junction temperature 0 °C to 125 °C
Storage temperature −65 °C to +150 °C
Thermal resistance, junction to case 5 °C/W
Pin 1 Input
Pin 2 Ground (joined to the metal tab)
Pin 3 Output

If this part is not available, use one of these instead

Read the warning under the part before you swap. A swap must match on voltage, pins, and pack, not on voltage alone.

  • LM7812 Positive Voltage Regulator SMD DPAK — practical substitute only, NOT a drop-in. It does the same 12V regulator job, but it comes in a surface-mount DPAK pack, not the TO-220 through-hole pack on this page. It only works if your board is reworked or an adapter is used to fit it. It sheds heat through board copper, not through a bolted heatsink, but that does not help unless the pack fits your board.

Warning: never swap on voltage alone. Check the voltage (12V), the pin order, the pack, and the heat plan first. If any one of those does not match, do not swap.

Other names for the same part (good to know)

Shoppers and repair techs call this same part by a few names. LM7812 is the plain part code most buyers type. lm7812 to-220 is the name buyers use when the through-hole pack matters. 12V 1A voltage regulator is the name buyers use when the ratings are what matters. If your board list calls for a 12V 1A positive regulator in a TO-220 package, this page is the right match. Do not judge by the code alone — check the voltage, the current, and the package too.

Frequently Asked Questions

What voltage does the LM7812 give out?

A fixed 12V. At room temperature the output sits between 11.5V and 12.5V.

What is the LM7812 pinout?

Pin 1 Input, Pin 2 Ground (joined to the metal tab), Pin 3 Output.

Can I use the DPAK version instead of this TO-220 part?

Only with board work. The DPAK version does the same 12V job, but it is a surface-mount part, not a through-hole TO-220 part. It will not drop into a TO-220 footprint.

How much current can it give?

1A typical, up to 1.5A with adequate heatsinking. Work out your heat first — the part must shed (input volts minus 12V) times load amps as heat.

What input voltage does it need?

The output is tested over a 14.5V to 27V input range, and the absolute input maximum is 35V. Stay inside the tested range for steady work.

What is the price of this part?

Check the live price on the website. The price shown on the product page is the current one.

Use note kept from the old page: this part was listed before as a stable 12V positive voltage regulator in a TO-220 package for power supply circuits and solar inverter systems, with minimal ripple and low noise, protecting sensitive components from voltage fluctuations, with overload, short-circuit and thermal protection, easy mounting and effective heat management for high-power applications, for industrial, automotive and renewable energy systems — and that use still stands.

You can view and download the datasheet for this part from the Download button on this page.

SKULM7812-IC TAGSIC

Reviews

4.3 12 reviews
Mehmood Aslam

Delivery bohot fast thi, shukriya.

Fahad Khan

Waqai maza agaya cheez dekh kar.

Owais Shah

Quick delivery, no hassles

Farhan Saeed

Loved the product, will buy again

Add a review

Your email address will not be published. Required fields are marked *

You may also like

Need Help?
Ask Here