Hall Effect Current Sensor Sinomags STB-20HA-A
Rs1,600
Description
Hall Effect Current Sensor Sinomags STB-20HA-A is a closed-loop Hall effect current sensor with TMR technology for measuring DC, AC, pulse and irregular-waveform current up to a 20A nominal value. It gives a 4V output at 20A from a ±15V supply, so it fits current sensing and overcurrent protection in solar inverters, UPS systems, variable frequency converters, DC dynamos and switched-mode power supplies. It does not fit jobs that need a 5V Arduino-style sensor module — this is an industrial sensor that needs a dual ±15V supply — and it does not fit a thick busbar, because the primary hole takes one wire up to 1.6mm diameter. This is an original, high-quality part.
What it does
The STB-20HA-A measures the current flowing through a wire passed through its aperture and gives out a voltage that follows that current. At 20A the output is 4V. Because it works on the closed-loop principle with TMR technology, it stays accurate and fast: linearity ±0.5%, accuracy ±0.8% at 25°C, step response 1.5µs and bandwidth 150kHz. It measures DC, AC, pulse and irregular waveform current, in both directions, with a measuring range of ±60A.
Key features
- Closed-loop TMR technology — fast and accurate current sensing
- 20A nominal current, ±60A measuring range
- 4V output at 20A (3.96–4.04V)
- ±15V ±5% dual supply
- Linearity ±0.5% of IPN, accuracy ±0.8% at 25°C
- Step response 1.5µs, bandwidth 150kHz (-3dB)
- Measures DC, AC, pulse and irregular waveform current
- Wide working temperature: -40°C to +85°C
- 6-pin through-hole package, 18.5 × 15.4 × 21mm, 13g
- UL94V-0 material, RoHS
Checks before you order
- Supply: Your board must provide a dual ±15V supply (±5%). This sensor does not run on 5V alone.
- Current rating: This is the 20A part. The same series also has 10A, 15A, 25A, 30A, 50A and 60A parts — order the rating your job needs.
- Primary wire: Pass one wire up to 1.6mm diameter through the aperture, one turn only.
- Pinout: 6 pins — 1: -Vcc (-15V), 2: GND (0V), 3: +Vcc (+15V), 4: Vout, 5: Primary input current (+), 6: Primary input current (-). Check the pinout in the datasheet before soldering.
- Marking: The part is marked “STB-HA/A 20” on its body — that is the same part as STB-20HA-A (series STB-HA/A, 20A variant).
- Not an ACS712 module: This is an industrial closed-loop sensor, not a 5V Arduino current sensor module. It does not fit Arduino-style 5V boards directly.
- Not L18P020D15: SunTech also sells the Tamura L18P020D15 (20A, open-loop Hall). Both are 20A sensors with a 4V output, but they are different parts with different pinouts — check which one your board needs before you order.
Specifications
All figures below are for the STB-20HA/A part at +25°C unless noted. No figure here was guessed.
| Parameter | Value |
|---|---|
| Type | Closed-loop Hall effect current sensor (TMR technology) |
| Primary nominal current (IPN) | 20A rms |
| Primary current measuring range (IPM) | ±60A |
| Output voltage (Vout) | 4V (3.96–4.04V) at 20A |
| Supply voltage (VC) | ±15V ±5% |
| Current consumption (IC) | 18 + IP×NP/NS mA (NS = 1000) |
| Linearity (εL) | ±0.5% of IPN |
| Electrical offset voltage (VOE) | ±40mV max (at 0A) |
| Accuracy at 25°C (X) | ±0.8% of IPN |
| Thermal drift of offset (TCVOE) | ±1% of IPN |
| Thermal drift of gain (TCVO) | ±1.5% |
| Step response time (tr) | 1.5µs |
| Frequency bandwidth (-3dB) (BW) | 150kHz |
| Primary conductor | 1.6mm diameter × 1 turn |
| Working temperature (TA) | -40°C to +85°C |
| Storage temperature (Tstg) | -40°C to +105°C |
| Absolute maximum supply voltage (Vcc_max) | ±18V |
| ESD rating (HBM) | 4kV |
| Pins | 6 (through-hole) |
| Dimensions | 18.5 × 15.4 × 21mm |
| Mass | 13g |
| Material | UL94V-0, RoHS |
Other names for the same part (good to know)
- STB-20HA/A
- STB-HA/A 20 (body marking)
- Sinomags STB-20HA-A
- 20A closed-loop TMR current sensor
- Sinomags STB-HA/A series 20A sensor
Frequently Asked Questions
What is the STB-20HA-A used for?
Measuring current in solar inverters, UPS systems, variable frequency converters, DC dynamos and switched-mode power supplies — also for overcurrent detection and protection.
What power supply does it need?
A dual ±15V supply (±5%). It does not work on 5V alone. The absolute maximum supply is ±18V.
What output do I get at 20A?
4V (3.96V to 4.04V). The output follows the measured current in both directions, up to a ±60A measuring range.
Is this the same as an ACS712 20A module?
No. The ACS712 is a 5V Arduino-style module. The STB-20HA-A is an industrial closed-loop TMR sensor with a ±15V supply, 4V output, 1.5µs response and 150kHz bandwidth.
What does the marking “STB-HA/A 20” mean?
It is the body marking of this same part: series STB-HA/A, 20A variant. The order code is STB-20HA-A.
What is the difference between STB-20HA-A and L18P020D15?
Both are 20A sensors with a 4V output, but the STB-20HA-A is a closed-loop TMR sensor (1.5µs, 150kHz, ±0.5% linearity) while the L18P020D15 is an open-loop Hall sensor (≤5µs, DC~100kHz, ±1% linearity). They have different pinouts, so check your board before you order.
Download the datasheet: use the Download button on this page for the official Sinomags STB-HA/A series datasheet (Ver 5.3).
SKU: STB-20HA-A-CT
Reviews
Be the first to share your experience with this part.
